Cranksets

Wheels Manufacturing BB30 Bottom Bracket Adaptor for Hollowtech II Cranks adapts 24mm Spindle Cranks (Shimano Hollowtech II, FSA, Race Face EXI, etc.) to work on BB30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin.

• Square taper interface • Only includes left crank

- Horizontal square interface - Only includes left crank

This Stages Power meter is built on to a non-drive Cannondale Si crank arm specifically to pair with Cannondale's Hollowgram Si crank — 2014 or newer. The Stages Power meter will also mate to the Hollowgram SISL2 model crank. This Stages Power meter is slimmer and up to 28% lower profile than their original meter. It's also sleeker, with a 17-percent reduction in frontal area, and they've made it stronger. The housing design increases the strength of the battery door and housing connection by 200-percent over the previous design. - Accuracy: ± 2% - Weight: Only adds 20gr to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Stages Support section - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibility: Training Peaks, Strava, Garmin Training Center and others

The Stages Power meter is built on to a non-drive FC-6800 crank arm specifically to pair with Shimano's Ultegra 6800 crank. The new Stages Power meter is slimmer, and up to 28% lower profile than the original meter. It's sleeker by way of a 17% reduction in frontal area, and they've also made it stronger. The new housing design increases the strength of the battery door and housing connection by 200% over the previous design. This Shimano Ultegra 6800 Stages Power meter is compatible with all Shimano Hollowtech II road drivetrains. - Accuracy: ± 2% - Power meter housing: new low profile design, with new door interface - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Support section - Device Compatibility: ANT+, Bluetooth Smart Ready Software - Compatibility: Training Peaks, Strava, Garmin Training Center and others

Sporting a supreme strength-to-weight ratio, Specialized's S-Works Carbon Road Crank Arms are super stiff and ready to propel you up the climbs. With a self-extracting bolt for easy maintenance, these hollow crank arms feature an oversized aluminum spindle with a Hirth coupling interface and a unidirectional carbon fiber finish. They fit Specialized road frames with an OSBB or Pressfit 30 bottom bracket shell. - Light and strong, these S-Works carbon road arms give you the competitive advantage. - Hollow carbon crank arms offer superior stiffness. - Oversized alloy spindle with Hirth coupling interface. - Fits Specialized road frames with OSBB or PF30 bottom bracket shell. - BB30 compatible. - Compatible with Shimano and SRAM drivetrains. - Finish: Unidirectional carbon fiber - Spider: 110BCD

This very light, stiff, and strong carbon crank spider optimizes your power transfer. - Stiff and lightweight. - For use with S-Works carbon road cranks.

For maximum pedaling efficiency, Shimano's 105 Compact Crankset boasts light, strong and stiff hollow, cold forged-aluminum arms, plus an integrated oversize-steel axle. The compact chainrings are also made of cold-forged aluminum and are ramped and pinned for quick, precise shifting.

Whether you're planning on riding a century, pushing the pace with friends or just like to ride fast, you'll appreciate the stiff and efficient power transfer of the Shimano 105 Crankset. It boasts hollow-forged-aluminum arms that are light, incredibly strong and rigid.

Shimano's Dura-Ace 11-Speed Hollowtech II Crankset has set the benchmark in strength-to-weight ratios, which is why it's proven itself at the highest echelon of competition. Made of cold-forged and CNC-machined aluminum, it has hollow crankarms and a hollow large chainring. Both chainrings also feature teeth perfectly designed to assist up- and down-shifts. Perhaps most unique is the 4-arm design that maximizes strength and rigidity where your pedal stroke is strongest. The result is legendary stiffness for awesome power transfer and precision shifting you'll love.

- Optimum Power Transfer - Best Balance For Lighter Weight (-7G) And Efficiency - New Designed Crank Arm - Maintains High Rigidity And Reduces Weight - Hollowglide - 4-Arm Construction Crankset - Adapted For Race Specific Disc Brake System - Shorter Length Of Rear Center With O.L.D. 135mm - Redesign The Gear Teeth Profile To Fit Wider Gear Pitch - 50-34T/53-39T/54-42T/55-42T/52-36T - Iconic Design - Chain Line: 43.5

Shimano's Dura-Ace Hollowtech II Crankset has always set the benchmark in strength-to-weight ratios, which is why it's proven itself at the highest echelon of competition. It's made of cold-forged and CNC-machined aluminum and has hollow crankarms and a hollow large chainring. Both chainrings also feature a new tooth design. The result is legendary stiffness for awesome power transfer and precision shifting you'll love. Plus, the Dura-Ace crankset is also lighter than many carbon models.

Shimano's R9100 series crankset achieves the ultimate in optimal power transfer. It does this through its broader Hollowtech II arm and a more reinforced outer chainring on its unique asymmetrical four-arm spider construction. The R9100 cranks set the highest standards for stiffness and lightness. With the first integrated power meter, you can expect extremely accurate data. The FC-R9100-P is Shimano’s first power meter, as well as Shimano’s first crank-integrated power meter on the market. It retains its unique asymmetrical four-arm spider construction, but with a ‘brain’ mounted on the inside. On its crank arm are the strain gauges. Working perfectly in sync with each other, you can use the extremely precise power data to improve your performance. - Accurate real time data - Compatible with 3rd party displays - Bluetooth / ANT technology - Hollowtech II construction - Hollowglide chain - 11-speed compatible - Waterproof in all conditions - ±2% accuracy of strain gage measured power - Integrated rechargeable battery - Simple zero reset with switch on transmitter - Average weight (170mm, w/o BB): 691 grams (53-39T)/679 grams (50-34T)

The Tourney TY501 crankset provides crisp, reliable shifting for your triple chainring drivetrain. - Precision indexed shifting - 8/7/6-speed compatible - 3 crank length specification available - Precise chain line control - Light and reliable shifting - Versatile performance - Wide compatibility with multiple components - Quick and precise assembly

Low weight, efficiency, and speed: That's what Shimano's Ultegra Crankset brings to every ride. The proprietary four-arm design sheds grams and increases stiffness for more power straight to the road. Computer-designed chainrings with optimally placed ramps and pins are a revolution in front shifting with fast, smooth gear changes that set the standard. A wide range of gearing options and crank lengths offers you the opportunity to find the crank that suits your riding style.

Shimano's Ultegra Crankset boasts hollow-forged-aluminum arms for weight savings and strength, an integrated-bottom-bracket-axle design for super-efficient power transfer and chainrings with ramps, pins and notched teeth for super-fast shifting.

You ride every trail like the competition is breathing down your neck. Shimano's XTR Hollowtech II Race Crankset was made just for you. The hollow, cold-forged aluminum crankarms are ultra light, but they're also exceptionally stiff for awesome power transfer and efficiency. Front shifts have never been this fast either, with Shimano's legendary chain rings and computer-designed shift ramps. CloseStep gear combos allow riders to tailor the chainring combos to suit their riding needs.

SRAM's Apex Crankset is designed for capable stiffness at an impressive weight. The cold-forged aluminum arms are tough, rigid and perfectly complement your favorite ride. SRAM's long-lasting Powerglide chainrings are hard anodized and designed for quick, positive shifting in all conditions. Plus, the Apex crankset comes with SRAM's smooth-spinning GXP bottom bracket.

Forget front derailleurs; SRAM's Force 1 Crankset brings a game-changing upgrade in performance and reliability to cyclocross, road, and other 700c disciplines. Force 1 combines the durability, simplicity and efficiency that SRAM is known for with their 1x mountain technology. - Single-ring drivetrain simplifies functionality - SRAM X-Sync: wide-tooth, narrow-tooth chainring technology provides maximum chain control - Chainrings available in 42, 50 (110 BCD), and 52 (130BCD) teeth to conquer every course from sand dunes to gravel-road assaults - Unidirectional carbon crank arm matched to a forged aluminum spider for lightweight and durability - Weight 679g-24mm, 172.5mm, 50T, no BB - Bottom bracket not included

SRAM's Force 22 Crankset uses unidirectional carbon arms with a forged aluminum spider and integrated bottom-bracket axle to ensure top-notch stiffness for awesome power transfer and exceptionally low weights. Experience phenomenal front shifting with SRAM's X Glide R chainrings that start out as 5mm-thick aluminum plates and then precision machined to eliminate all unessential material while retaining extreme stiffness. With so much great technology and 11-speed compatibility, they're a force to be reckoned with.

SRAM Force crank spiders are for repairing your crank or converting it to different gearing. Available in 110mm and 130mm BCDs.

Competition-focused technology is available to everyone with SRAM's Force Crankset. Its unidirectional carbon design and oversized 30mm bottom-bracket axle ensure top-notch stiffness for awesome power transfer and exceptional lightness. And, because being light is nothing without being tough, the Force proudly boasts SRAM's hard-anodized PowerGlide chainrings for long-lasting durability and lightning-quick shifts.

Competition-focused technology is available to everyone with SRAM's Force Crankset. Its unidirectional carbon design and oversized 30mm bottom-bracket axle ensure top-notch stiffness for awesome power transfer and exceptional lightness. And, because being light is nothing without being tough, the Force proudly boasts SRAM's hard-anodized PowerGlide chainrings for long-lasting durability and lightning-quick shifts.

SRAM's GX 2x10 Crankset delivers consistent performance every time out. Featuring SRAM’s X-Glide chainrings, the GX crankset is engineered for 2x10 shifting performance. Flawless shifting means you’ll never again compromise your speed and power in unpredictable off-road terrain. No more missed shifts. X-Glide puts you in the right gear, right now. - 10-Speed - 6000 series AL - X-GLIDE 2x10 shifting technology - Fat Bike GXP: 100mm spindle

SRAM's GX-1400 1x Crankset delivers consistent performance every time out. Featuring SRAM’s X-Sync tooth profile, the GX single-chainring crankset is engineered for complete chain control. Each tooth’s thickness is CNC machined to work seamlessly with the chain’s inner and outer links. - Open Core and X-Sync Technology - CNC machined 7075, two-tone anodized X-Sync chainring (30/32T) - Weight: 680g (GXP, 175mm, 32T)

Already a legend in its time, the SRAM RED crankset is now available with refreshed graphics to complement the SRAM RED eTap componentry. The SRAM RED crankset features a completely hollow construction all the way to the spider. Its hidden bolt pattern makes better use of carbon fiber to further improve stiffness and shed weight. As always, for seamless, flawless performance and Yaw compatibility, pair this crank with X-GlideR chainrings. - SRAM Road 11-speed compatible - Compatible with SRAM RED eTap components - Exogram technology uses a large, hollow cross section all the way to the spider, minimizing weight while maximizing stiffness - SRAM's stiffest crank ever - Hidden bolt pattern leverages the characteristics of carbon fiber while presenting a sleek appearance - Stiffer X-GlideR chainrings feature thicker construction and advanced shift timing pins and ramps, which are optimized for shifting with the Yaw front derailleur - Arm Material: Carbon - Chainring Material: Machined alloy - Weight: 557 grams (BB30 172.5mm 53x39 BB not included) - Compatibility: SRAM RED & SRAM Force Yaw Front Derailleur, SRAM RED 22 & PC1170 chains - Finish: Carbon - Bottom Bracket Compatibility: BB30, PressFit 30

Forget front derailleurs; SRAM's Rival 1 Crankset brings a game-changing upgrade in performance and reliability to cyclocross, road, and other 700c disciplines. It combines the durability, simplicity, and efficiency SRAM is know for on the road with their 1x mountain technology, X-Sync. - Single-ring drivetrain simplifies functionality - Forged aluminum with detachable spider: 42T and 52T X-Sync tall, square tooth design provides maximum control - Sharp, narrow tooth profile and rounded chamfer edges help manage a deflected chain - Mud-clearing recesses for the inner chain links and rollers - Weight: 799g (24mm spindle, 172.5mm, 42T, no BB)

SRAM's Rival 22 performs on par with more expensive cranksets, but at a bargain value. The crankarms are hollow and forged from 6066 aluminum for maximum strength with minimum weight. Because lightness is nothing without toughness, the Rival crankset proudly boasts SRAM's X Glide R chainrings that are specifically designed for use with the Yaw front derailleur. Durability and reliable shifting are your allies with Rival 22.

The SRAM S350-1 crankset brings quiet simplicity thanks to SRAM 1x technology. Featuring SRAM’s X-SYNC tooth profile, the S350-1 crankset is engineered for complete chain control at a great value. Each tooth’s thickness is CNC-machined to work seamlessly with the chain’s inner and outer links. And with four available chainrings you can personalize the gear range. - Alternative to Rival 1 crankset - Compatible with 130mm, 135mm and 142mm OLD frames - SRAM 1x simplicity and control - Durable forged aluminum with integrated spider - X-Sync chainrings have alternating wide and narrow teeth for maximum chain control - Compatible with SRAM 11 and 10 speed chains - BB Included: No - Chainrings Included: Yes - Color: Black - Crank Intended Use: Road - Drivetrain Speeds: 10, 11

The X01 Eagle DUB crankset is designed to be tough; ready for aggressive Trail and Enduro riding. The Carbon-tuned crankset paired with DUB technology simplifies the relationship of the spindle to the bottom bracket. DUB-powered cranksets mean simplicity, compatibility, and durability. - SRAM DUB technology creates a lighter, stiffer and stronger crankset - Carbon-tuned lay-up crank design provides extreme stiffness and light weight - Included direct mount X-SYNC 2 chainring provides significantly quieter performance, with better mud clearing and durability - Chainring is designed specifically for Eagle chains and drivetrains - DUB compatible bottom bracket sold separately - Boost Compatible - BB Included: No - Chainring BCD: Sram Direct Mount - Crank Intended Use: Mountain - Number of Chainrings: Single - Drivetrain Speeds: 12, 11, 10 - Spindle Interface Type: SRAM DUB - Chainline/Hub Compatibility: 141/148 Boost Hubs