Campagnolo's Record EPS V2 Power Unit is the reliable brain of Campy's electronic shifting. In order to keep your bike looking sleek, the mounting options allow it to sit inside your bike's frame. The 3-cell, 12-volt Lithium-ion battery delivers up to 1,200 miles on a single charge. It also houses the electronics necessary to deliver pinpoint shifting precision to the front and rear derailleur mechanisms (sold separately). For example, if you're cross-chained, the system immediately senses it and moves the front derailleur ever so slightly to avoid chain rub. Plus, the one-piece, ultrasonically-sealed unit is impervious to water or road vibration.
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 30mm - Width: 7mm
Don't let chain slap damage your frame — pick up Lezyne's C-Stay Protector. It's made of heavy-duty neoprene with a slip resistant rubber inner and a Velcro closure to keep it in place.
Profile Design's Lux Pads keep both performance and comfort high, exactly where they need to be when you're pushing your boundaries. These velcro backed pads fit Profile Designs F-35 armrests (sold separately), and feature EVA foam, an anti-microbial cover, and a contoured edge for improved long-term comfort. They're even available in three thicknesses so you can dial in your fit to perfection.
If you put in a lot of miles and/or sweat a lot, your shifter hoods probably need freshening up. Grab a pair of Shimano STI Lever Hoods to make your bike feel new again. - Fits Dura-Ace ST-R9120 levers
- Model: Derailleur Bolt & Nut - Compatibility: Mounts rear bracket to frame
- Black carbon fiber weave headset spacers for tuning ride height - No logos - Includes five (5) 1-1/8" x 5mm spacers
All Wheels Mfg. replacement derailleur hangers are produced in Colorado to exacting tolerances. - Replaces Scott part #254090-222 - For standard mount derailleurs - Attaches to frame with (1) special M4 socket head screw (sold separately) - CNC machined 6061 aluminum - Black anodized finish
Interlok spacers nest into the lip of Cane Creek headset uppers for a rock solid, flex-free fit. - Composite construction
$1.00 - $50.00
- Allows quick chain removal without tools - MissingLink 410HD|~|1sp|~|BMX Heavy Duty chain|~|9.4mm|~|each|~| - MissingLink 410|~|1sp|~|BMX|~|8.6mm|~|each|~| - MissingLink II|~|8sp|~|all|~|7.1mm|~|6/card|~| - MissingLink-9|~|9sp|~|all|~|6.6mm|~|6/card|~| - MissingLink-10R|~|10sp|~|KMC, Shimano, SRAM|~|5.9mm|~|6/card|~| - MissingLink-10CR|~|10sp|~|Campagnolo only|~|5.9mm|~|6/card|~| - MissingLink-11|~|11sp|~|Campy, KMC, Shimano|~|5.5mm|~|6/card|~|
Shim spacers can be placed between bearing and compression cover in IS headsets to fine tune the fitment.
KMC 3/16" Master Link Chain Links - For 3/16" chain, extra wide - Extra-wide, for non-derailleur bikes: BMX, cruisers, etc - Perfectly fits on KMC 415H & 415H-NP chains
Stainless steel pedal washers - Sold in pairs
- Half-link connector allows you to add or subtract half of one link (1/2 inch) from the chain in order to optimize chain tension - Uses standard chain pin connector and tool
- Replacement retaining clip for the Surly Tuggnut/Snuggnut
Replacement M5 x 10 Socket Head Screw fastener for derailleur hangers. - Head Type: Socket Head Cap - Drive Type: Hex Socket - Thread Size: M5x0.8mm - Length Under Head: 10mm - Material: Stainless Steel - Hex Key Size: 4mm - Bag of 5
$2.65 - $3.50
Replacement M5 x 8 Flat Head Screw fastener for derailleur hangers. - Thread: M5-0.8 - Overall Length: 8mm - Material: Steel - Use with 3mm hex wrench - Bag of 5
Replacement M3 x 10 Socket Head Screw fastener for derailleur hangers. - Thread: M3-0.5 - Thread length: 10mm - Use with 2.5mm hex wrench - Bag of 5
Shimano Mountain Deore XT M8000 Shift Pod Cable Adjusting Unit
Shimano E-tube Dummy Plugs - Extra E-Tube plugs for sealing unused ports on shifters or junction boxes - Sold each
Shimano Front Derailleur Cable Fixing Assembly
- QR adapter washer for the Surly Tuggnut/Hurdy/Snuggnut
$3.25 - $14.75
Aluminum headset stack spacers precision-cut to ensure proper headset function. - Precision-cut for proper function - Inner Diameter: 28.9mm - Outer Diameter: 34.4mm - Precision-machined aluminum
$3.50 - $51.50
- Replacement Rotor Bolt kits for Formula rotors - 6/pack
The Greenfield RetroKit is a retro-mounting kickstand plate designed with a cutaway to clear derailleur cables. - Fits all Greenfield kickstands and most generics - Made in the USA
Strain relief for servicing RockShox Reverb hydraulic lines. - Fits all generations of Reverb
Bolts, clamps and washers for Thomson Seatposts and Seat Clamps. - Sold individually, includes bolt, washer and nut
The Tanpan ferrule converts standard Tanpans to Tanpan inlines. - Coverts Tanpan into Tanpan Inline
$3.99 - $39.99
Jagwire's Brake or Shift Cable Tips are made of lightweight, corrosion-resistant and durable aluminum and are the right size to nicely fit over the ends of up to 1.8mm-diameter cables. These caps are crimped in place on the cables to prevent fraying and ensure your cables last a long time. The tips come in colors to add a little style to your bike.
The Odyssey stem bolt pack features 6 - 6mm stem bolts that are M8 x 1.25mm thread.
Page 1 of 30 Next page